Conductive atomic force microscopy

This article relies excessively on references to primary sources. Please improve this article by adding secondary or tertiary sources. Find sources: "Conductive atomic force microscopy" – news · newspapers · books · scholar · JSTOR (November 2017) (Learn how and when to remove this message)

In microscopy, conductive atomic force microscopy (C-AFM) or current sensing atomic force microscopy (CS-AFM) is a mode in atomic force microscopy (AFM) that simultaneously measures the topography of a material and the electric current flow at the contact point of the tip with the surface of the sample. The topography is measured by detecting the deflection of the cantilever using an optical system (laser + photodiode), while the current is detected using a current-to-voltage preamplifier.^[1] The fact that the CAFM uses two different detection systems (optical for the topography and preamplifier for the current) is a strong advantage compared to scanning tunneling microscopy (STM). Basically, in STM the topography picture is constructed based on the current flowing between the tip and the sample (the distance can be calculated depending on the current). Therefore, when a portion of a sample is scanned with an STM, it is not possible to discern if the current fluctuations are related to a change in the topography (due to surface roughness) or to a change in the sample conductivity (due to intrinsic inhomogeneities).

The CAFM is usually operated in contact mode; the tip can be kept at one location while the voltage and current signals are applied/read, or it can be moved to scan a specific region of the sample under a constant voltage (and the current is collected). Recently, some manufacturers provide the option of measuring the current in semi-contact mode.^[2] The CAFM was first developed by Sean O'Shea and co-workers at the University of Cambridge in 1993,^[3] and it is referred to in the literature by several names, including C-AFM, local-conductivity AFM (LC-AFM), conductive probe AFM (CP-AFM), conductive scanning probe microscopy (C-SPM) or conductive scanning force microscopy (C-SFM), although CAFM is the most widespread.

In order to transform an AFM into a CAFM, three elements are required: i) the probe tip must be conductive, ii) a voltage source is needed to apply a potential difference between the tip and the sample holder, and iii) a preamplifier is used to convert the (analogical) current signal into (digital) voltages that can be read by the computer.^[1] In CAFM experiments, the sample is usually fixed on the sample holder using a conductive tape or paste, being silver paints the most widespread.^[4] A Faraday cage is also convenient to isolate the sample from any external electrical interference. Using this setup, when a potential difference is imposed between tip and sample an electrical field is generated, which results in a net current flowing from tip-to-sample or vice versa. The currents collected by the CAFM obey the relationship:

${\displaystyle I=J\cdot A_{eff}}$

where I is the total current flowing through the tip/sample nanojunction, J is the current density and A_eff is the effective emission area through which electrons can flow (from now on we will refer to it just as effective area).^[1] The most common mistake in CAFM research is to assume that the effective emission area (A_eff) equals the physical contact area (A_c). Strictly, this assumption is erroneous because in many different tip/sample systems the electrical field applied may propagate laterally. For example, when the CAFM tip is placed on a metal the lateral conductivity of the sample is very high, making (in principle) the whole sample surface area electrically connected (A_eff equals the area covered by the metallic film/electrode).^[5][6] A_eff has been defined as:"the sum of all those infinitesimal spatial locations on the surface of the sample that are electrically connected to the CAFM tip (the potential difference is negligible). As such, A_eff is a virtual entity that summarizes all electrically relevant effects within the tip/sample contact system into a single value, over which the current density is assumed to be constant."^[1] Therefore, when the CAFM tip is placed in contact with a metal (a metallic sample or just a metallic pad on an insulator), the lateral conductivity of the metal is very high, and the CAFM tip can be understood as a current collector (nanosized probe station);^[1][5][6] on the contrary, if the CAFM tip is placed directly on an insulator, it acts as a nanosized electrode and provides a very high lateral resolution. The value of A_eff when a Pt-Ir coated tip (with a typical radius of 20 nm) is placed on a SiO₂ insulating film has been calculated to be typically 50 nm².^{[7][8][9][10][11][12][13]} The value of A_eff can fluctuate depending on the environmental conditions, and it can range from 1 nm² in ultra high vacuum (UHV) to 300 nm² in very humid environments.^[14][15][16] On well-defined single crystal surfaces under UHV conditions it has even been demonstrated that measurements of the local conductivity with atomic resolution are possible.^[17]

Common problems in conventional CAFM include difficulty in managing high and low currents and avoiding unwanted side-effects such as the Joule, Bimetallic and local oxidation effects when using high currents.^[18] In order to produce accurate and reproducible measurements, constant tip replacements, re-setting up of the AFM, re-finding the area of interest are needed – all at the expense of time, money and effort. A book by Mario Lanza explains these issues with supporting data (Chapter 12, Pacheco and Martinez. 2017).^[1] The study further describes a more effective conductive measuring concept, a module named ResiScope II from AFM manufacturer Concept Scientific Instruments, which overcomes these issues. This module allows to perform current/resistance measurements over 10 orders of magnitude (from fA to mA). This study demonstrates how the ResiScope can efficiently map both highly conductive and insulating domains without undesirable side-effects like probe-induced local oxidation, bimetallic effect or melting of the conductive coating by Joule effect.

ResiScope II can potentially transform the understanding of variable conductivity samples using Conductive AFM.

CAFM was initially used in the field of nanoelectronics to monitor the electrical properties of thin dielectrics with very high lateral resolution. The first CAFM development in 1993 had the goal of studying the local tunneling currents through 12 nm thick SiO₂ films.^[3] In 1995 and 1996, O'Shea^[19] and Ruskell^[20] further improved the lateral resolution of the CAFM technique, achieving values of 10 nm and 8 nm, respectively. This enhanced resolution allowed to observe the first topographic-current correlations, and the inhomogeneity observed in the current maps was associated to the presence of local native defects in the oxide. Following works by Olbrich^[21][22][23] and Ebersberger^[24] reported that, in SiO₂ films thinner than 5 nm, the tunneling current increases exponentially with thickness reductions. Consequently, thickness fluctuations of tenths of nanometer in the SiO₂ film could create electrically weak spots that reduce the reliability of the whole dielectric film, as the dielectric breakdown (BD) is a stochastic process. The capability of the CAFM for determining the thickness of thin oxides was further demonstrated by Frammelsberger and co-workers^[7][25] who statistically analyzed more than 7200 I-V curves, and reported SiO₂ thicknesses with a sensitivity of ±0.3 nm. Other local phenomena like charge trapping,^[26] trap assisted tunneling^{[27][28][29][30][31][32]} and stress induced leakage current (SILC)^[33] can be also easily monitored with CAFM. In general, the CAFM can monitor the effect of any process that introduces local changes in the structure of the dielectric, including thermal annealing,^{[34][35][12][36][37][16][38]} dopping^[39] and irradiation,^[40][41][42] among others.

Apart from monitoring the electrical properties of a dielectric, the CAFM can be also used to alter its properties by applying an electrical field locally. In particular, the CAFM is especially useful to determine which locations of the samples lead to premature BD, which can provide essential information about the reliability of the samples. The CAFM also helped to confirm the percolation theory of the BD by experimentally proving that this is a very local phenomenon that occurs in small areas typically below 100 nm².^[33] Lateral propagations of the BD event can also be detected by CAFM.^[15][43][44] The severity of the BD event can also be studied from the dielectric breakdown induced epitaxy,^{[27][45][46][47]} which can be observed from subsequent topographic images collected with the CAFM after the voltage ramp. Similarly, the analysis of the BD recovery (resistive switching, RS) can also be monitored by CAFM.^{[48][49][50][51]} All the capabilities of the CAFM for studying resistive switching in dielectrics have been summarized in the review article of reference.^[52] Unlike a normal AFM, the CAFM can be also used to perform local photolithography via bias-assisted local anodic oxidation (LAO). Nowadays the CAFM technique has expanded to many other fields of science, including physics, materials science, chemistry and engineering (among many others), and it has been used to study different materials and/or structures, including nanoparticles,^[53][54] molecules,^[55] nanowires,^[56] carbon nanotubes,^[57] two dimensional (2D) materials,^{[58][59][60][61][62]} coatings,^[63][64][65] photoelectricity^[66] and piezoelectricity^[67] (among others). As of June 14 of 2016, the CAFM had been used in 1325 journal research articles, and it has become a popular tool in nanosciences.^[1]

There is now an increasing use of the electrical characterisation capabilities of AFM in nanotechnology-based fields such as energy harvesting, organic/polymer-based electronics, semiconductors etc. Flexible electronics based on organic compounds are gaining popularity as soft electrical materials.

Currently, two different methods are used for Conductive AFM (C-AFM) measurements of soft materials such as conductive polymers.^[1]

Sinusoidal Regime Method

In the Sinusoidal Regime method, the cantilever is mechanically excited in the range of 100–2000 Hz i.e. well below its natural resonance frequency. The tip of the cantilever interacts with the substrate periodically during the bottom part of its sinusoidal displacement. This method allows easy imaging of soft samples by controlling the amplitude of the movement of the tip. However, some quantitative measurements cannot be performed (electrical, thermal, etc…) because the force exerted by the tip on the sample is variable.

Linear Regime Method

The Linear Regime Method is based on the force versus distance spectroscopy curves. In this quasi-static approach, the cantilever follows an approach-retract cycle towards the sample with constant velocity. Hook’s Law is used to select the force to be exerted. F=k*z, where F is the applied force, k is the cantilever constant and z is the cantilever deflection relative to the rest deflection position. However, this method is slow with an approach-retract cycle of 1 sec. At this rate, it can take up to 3 days to measure a standard 512 x 512 image.

A new approach to resolve these issues is the Soft ResiScope mode which combines fast point contacts and constant force.^[68]

The main problem of the CAFM is that the probes are more expensive and wear out faster than those used in topographic AFM maps, mainly due to the high current densities flowing through the tip/sample nanojunction, but also due to lateral friction. The premature degradation of a CAFM tip not only increases the cost of the experiments, but also reduces the reliability of the data collected. For this reason, when using CAFM, tip conductivity characterization (using a reference sample) before and after the experiments is highly recommended; only if the CAFM tip holds the same conductivity before and after is the data collected considered reliable. The first types of conductive nanoprobes used in CAFM experiments, which are still widely used nowadays, consist on standard silicon nanoprobes (as those used in topographic AFM measurements) varnished with thin metallic films, including Pt, Au, Ru, Ti and Cr, among others.^[3][7][69] The varnish should be thick enough to withstand the large current densities and frictions, and at the same time thin enough to not increase significantly the radius of the tip apex, maintaining its sharpness and ensuring a high lateral resolution of the CAFM technique. As mentioned, the lifetime of the metal-varnished tips for CAFM experiments is much shorter than in any other AFM mode, mainly due to metallic varnish melting and loss of tip mass during the scans. To solve this problem, CAFM silicon tips varnished with hard materials like phosphorus-doped diamond have appeared.^[69] The main problems of diamond-coapted CAFM tips are: i) they are much more expensive, and ii) they are very stiff and can damage (scratch) the surface of the samples under tests. Another option is to use sharpened metallic wires as the tip, but also the use of hone techniques increases their price (compared to metal-coated Si tips). Furthermore, these tips can also degrade (lose their conductivity) by particle adhesion. A cheap and effective methodology to protect CAFM tips from degrading is to coat them with graphene, which can withstand well the high current densities and mechanical friction. Moreover, graphene is inert and slows down particle adhesion to the tip apex.

The analogical current signals flowing through the tip/sample nanojunction are sent to the preamplifier, which transforms them into digital voltages that can be read by the data acquisition (DAQ) card of the computer. Many manufacturers integrate the preamplifier in the so-called "CAFM application module", which is a removable component that can be fixed to the AFM (usually very near to the tip to minimize the electrical noise) to perform conductivity measurements. Similarly, many other modules allow AFMs to perform other operations, like scanning capacitance microscopy (SCM) or scanning spreading resistance microscopy (SSRM). In most CAFM experiments the currents measured typically can range between a few picoamperes and hundreds of microamperes, while the voltages readable by the DAQ card usually range between -3 V to +3V.^[70] Therefore, the preamplifier needs to provide a very low noise and a high transimpedance (gain). Figure 2 shows the simplified schematic of a typical low noise preamplifier for CAFM measurements,^[71] in which some elements can be distinguished: i) an operational amplifier with high input impedance; ii) a feedback resistor (R_f) and its parasite capacitor (C_s) and Johnson noise (e_t) associated effects; iii) a noise voltage source associated to the operational amplifier (e_n); and iv) a capacitance associated to the input interconnections (C_i). A correct selection of the electrical components is essential to achieve good and reliable CAFM data acquisition. For example, the value of R_f is not trivial: a very high value of R_f improves the noise-signal ratio, while reduces the bandwidth of the preamplifier. Therefore, the value of R_f should be chosen to provide enough bandwidth and a noise level below the current values that we want to measure. The parameter e_n can be easily reduced by using a commercial low noise operational amplifier. The capacitance associated to the connections (C_i) can be easily minimized by placing the preamplifier as near as possible to the conductive tip. The company FEMTO, one of the world leading manufacturers of preamplifiers compatible with CAFMs, can provide devices with electrical noise as low as 3 fA and a gain up to 10¹³ V/A.^[72] Nevertheless, the main limitation of CAFM preamplifiers is their narrow current dynamic range, which usually allows collecting electrical signals only within three or four orders of magnitude (or even less). To solve this problem preamplifiers with an adjustable gain can be used to focus on specific ranges.^[72] A more sophisticated solution for this problem is to combine the CAFM with a sourcemeter,^[73][74] semiconductor parameter analyzer or with a logarithmic preamplifier,^[75] which can capture the currents flowing through the tip/sample system at any range and with a high resolution.