Niobium capacitor

A niobium electrolytic capacitor (historically also Columbium capacitor^[1][2]) is an electrolytic capacitor whose anode (+) is made of passivated niobium metal or niobium monoxide, on which an insulating niobium pentoxide layer acts as a dielectric. A solid electrolyte on the surface of the oxide layer serves as the capacitor's cathode (−).

Niobium capacitors are available in SMD packaging and compete with tantalum chip capacitors in certain voltage and capacitance ratings. They are available with a solid manganese dioxide electrolyte.

Like most electrolytic capacitors, niobium capacitors are polarized components. Reverse voltages or ripple currents higher than specified tolerances can destroy the dielectric and thus the capacitor; the resulting short circuit can cause a fire or explosion in larger units.

Niobium capacitors were developed in the United States and the Soviet Union in the 1960s. Since 2002 they have been commercially available in the West, taking advantage of the lower cost and better availability of niobium relative to tantalum.

Niobium is a sister metal to tantalum. Niobium has a similar melting point (2744 °C) to tantalum and exhibits similar chemical properties. The materials and processes used to produce niobium-dielectric capacitors are essentially the same as for existing tantalum-dielectric capacitors. However, niobium as a raw material is much more abundant in nature than tantalum and is less expensive. The characteristics of niobium electrolytic capacitors and tantalum electrolytic capacitors are roughly comparable.

Niobium electrolytic capacitors can be made with high purity niobium as the anode but the diffusion of oxygen from the dielectric (Nb₂O₅) into the niobium anode metal is very high, resulting in leakage current instability or even capacitor failures. There are two possible ways to reduce oxygen diffusion and improve leakage current stability – either by doping metallic niobium powders with nitride into passivated niobium nitride or using niobium oxide (NbO) as anode material. Niobium oxide is a hard ceramic material characterized by high metallic conductivity. Niobium oxide powder can be prepared in a similar structure to that of tantalum powder and can be processed in a similar way to produce capacitors. It also can be oxidized by anodic oxidation (anodizing, forming) to generate the insulating dielectric layer. Thus two types of niobium electrolytic capacitors are marketed, those using a passivated niobium anode and those using a niobium oxide anode. Both types use niobium pentoxide (Nb₂O₅) as the dielectric layer.

Niobium, similarly to tantalum and aluminum, is a so-called valve metal. Placing such a metal in contact with an electrolytic bath and applying a positive voltage to it forms a layer of electrically insulating oxide whose thickness corresponds to the applied voltage. This oxide layer acts as the dielectric in an electrolytic capacitor.

This property of niobium was known since the beginning of the 20th century. Although niobium is more abundant in nature and less expensive than tantalum, its high melting point of 2744 °C hindered the development of niobium electrolytic capacitors.

In the 1960s, the higher availability of niobium ore compared with tantalum ore prompted research into niobium electrolytic capacitors in the Soviet Union.^[3] Here they served the same purpose as tantalum capacitors in the West. With the collapse of the Iron Curtain, the technology became better-known in the West, with major capacitor manufacturers taking interest in the late 1990s. The materials and processes used to produce niobium capacitors are essentially the same as for tantalum capacitors. Rising tantalum prices in 2000 and 2001 encouraged the development of niobium electrolytic capacitors with manganese dioxide and polymer electrolytes, which have been available since 2002.^[4][5]

Every electrolytic capacitor can be thought of as a "plate capacitor" whose capacitance increases with the electrode area (A) and the dielectric permittivity (ε), and decreases with the dielectric thickness (d).

${\displaystyle C=\varepsilon \cdot {\frac {A}{d}}}$

The dielectric thickness of niobium electrolytic capacitors is very thin, in the range of nanometers per volt.^[6] This very thin dielectric layer, combined with a sufficiently high dielectric strength, allows niobium electrolytic capacitors to achieve a high volumetric capacitance comparable to tantalum capacitors.

The niobium anode material is manufactured from a powder sintered into a pellet with a rough surface structure intended to increase the electrode surface area A compared to a smooth surface with the same footprint. This increase in surface area can increase the capacitance by a factor of up to 200 for solid niobium electrolytic capacitors, depending on the rated voltage.^[7]

The properties of the niobium pentoxide dielectric layer, compared with a tantalum pentoxide layer, are given in the following table:^[8]

The higher permittivity and lower breakdown voltage of niobium pentoxide relative to tantalum pentoxide results in niobium capacitors and tantalum capacitors having similar sizes for a given capacitance and a rated voltage.

• Construction of a solid niobium chip capacitor
• 
  The capacitor cell of a niobium electrolytic capacitor consists of sintered niobium or niobium monoxide powder
• 
  Schematic representation of the structure of a sintered niobium electrolytic capacitor with solid electrolyte and the cathode contacting layers
• 
  Construction of a typical SMD niobium electrolytic chip capacitor with solid electrolyte

A typical niobium capacitor is a chip capacitor and consists of niobium or niobium oxide powder pressed and sintered into a pellet as the anode of the capacitor, with the oxide layer of niobium pentoxide as dielectric, and a solid manganese dioxide electrolyte as the cathode.

The combination of anode materials for niobium and tantalum electrolytic capacitors and the electrolytes used has formed a wide variety of capacitor types with different properties. An outline of the main characteristics of the different types is shown in the table below.

Tantalum and niobium electrolytic capacitors with solid electrolyte as surface-mountable chip capacitors are mainly used in electronic devices in which little space is available or a low profile is required. They operate reliably over a wide temperature range without large parameter deviations.^{[4][6][8][9][10]}

In order to compare the different characteristics of the different electrolytic chip capacitor types, specimens with the same dimensions and of comparable capacitance and voltage are compared in the following table. In such a comparison the values for ESR and ripple current load are the most important parameters for the use of electrolytic capacitors in modern electronic equipment. The lower the ESR the higher the ripple current per volume, thus the better the functionality of the capacitor in the circuit.

(1) 100 μF/10 V, unless otherwise specified,

(2) calculated for a capacitor 100 μF/10 V,

The phenomenon that can electrochemically form an oxide layer on aluminum and metals like tantalum or niobium, blocking an electric current in one direction but allowing it to flow in the other direction, was discovered in 1875 by the French researcher Eugène Ducretet. He coined the term "valve metal" for such metals. Charles Pollak (born Karol Pollak) used this phenomenon for an idea of a polarized "Electric liquid capacitor with aluminum electrodes". In 1896 Pollak obtained a patent for the first electrolytic capacitor.^[11] The first tantalum electrolytic capacitors with wound tantalum foils and non-solid electrolyte were developed in 1930 by Tansitor Electronics Inc., USA, and used for military purposes.^[12]

The development of solid electrolyte tantalum capacitors began in the early 1950s as a miniaturized, more reliable low-voltage support capacitor to complement the newly invented transistor. The solution found by R. L. Taylor and H. E. Haring of the Bell Labs was based on experience with ceramics. They ground down tantalum to a powder, pressed this powder into a cylindrical form and then sintered the powder particles into a pellet ("slug") at high temperatures, between 1500 and 2000 °C, under vacuum conditions.^[13][14] These first sintered tantalum capacitors used a non-solid electrolyte not consistent with the concept of solid state electronics. 1952 a targeted search in the Bell Labs for a solid electrolyte by D. A. McLean and F. S. Power led to the invention of manganese dioxide as a solid electrolyte for a sintered tantalum capacitor.^[15]

Niobium electrolytic capacitors as discrete components are not ideal capacitors, they have losses and parasitic inductive parts. All properties can be defined and specified by a series equivalent circuit composed out of an idealized capacitance and additional electrical components which model all losses and inductive parameters of a capacitor. In this series-equivalent circuit the electrical characteristics are defined by:

• C, the capacitance of the capacitor
• R_leakage, the resistance representing the leakage current of the capacitor
• R_ESR, the equivalent series resistance which summarizes all ohmic losses of the capacitor, usually abbreviated as "ESR"
• L_ESL, the equivalent series inductance which is the effective self-inductance of the capacitor, usually abbreviated as "ESL".

Using a series equivalent circuit instead of a parallel equivalent circuit is specified by IEC/EN 60384-1.

The electrical characteristics of niobium electrolytic capacitors depend on structure of the anode and the type of electrolyte. The capacitance value of the capacitor depends on measuring frequency and temperature. The rated capacitance value or nominal value is specified in the data sheets of the manufacturers and is symbolized C_R C_N. The standardized measuring condition for electrolytic capacitors is an AC measuring method with a frequency of 100/120 Hz. The AC measuring voltage shall not exceed 0,5  V  AC-RMS.

The percentage of allowed deviation of the measured capacitance from the rated value is called capacitance tolerance. Electrolytic capacitors are available in different tolerance series, whose values are specified in the E series specified in IEC 60063. For abbreviated marking in tight spaces, a letter code for each tolerance is specified in IEC 60062.

• rated capacitance, E3 series, tolerance ±20%, letter code "M"
• rated capacitance, E6 series, tolerance ±20%, letter code "M"
• rated capacitance, E12 series, tolerance ±10%, letter code "K"

Referring to IEC/EN 60384-1 standard the allowed operating voltage for niobium capacitors is called "rated voltage U_R " or "nominal voltage U_N". The rated voltage U_R is the maximum DC voltage or peak pulse voltage that may be applied continuously at any temperature within the rated temperature range T_R (IEC/EN 60384-1).

The voltage proof of electrolytic capacitors decreases with increasing temperature. For some applications it is important to use a higher temperature range. Lowering the voltage applied at a higher temperature maintains safety margins. For some capacitor types therefore the IEC standard specifies a "temperature derated voltage" for a higher temperature, the "category voltage U_C". The category voltage is the maximum DC voltage or peak pulse voltage that may be applied continuously to a capacitor at any temperature within the category temperature range T_C. The relation between both voltages and temperatures is given in the picture right (or above, on mobile devices).

Lower voltage applied may have positive influences for tantalum (and niobium) electrolytic capacitors. Lowering the voltage applied increases the reliability and reduces the expected failure rate.^[16]

Applying a higher voltage than specified may destroy electrolytic capacitors.

The surge voltage indicates the maximum peak voltage value that may be applied to electrolytic capacitors during their application for a limited number of cycles. The surge voltage is standardized in IEC/EN 60384-1. For niobium electrolytic capacitors the surge voltage shall be not higher than round 1.3 times of the rated voltage, rounded off to the nearest volt. The surge voltage applied to niobium capacitors may influence the capacitors failure rate.

Like other electrolytic capacitors, niobium electrolytic capacitors are polarized and require the anode electrode voltage to be positive relative to the cathode voltage.

General information to impedance, ESR, dissipation factor tan δ, ripple current, and leakage current see electrolytic capacitor

For general information on reliability and failure rate see electrolytic capacitor.

The life time, service life, load life or useful life of electrolytic capacitors is a special characteristic of non-solid electrolytic capacitors, especially non-solid aluminum electrolytic capacitors. Their liquid electrolyte can evaporate over time, leading to wear-out failures. Solid niobium capacitors with manganese dioxide electrolyte have no wear-out mechanism, so the constant failure rate lasts up to the point when all capacitors have failed. They don't have a life time specification like non-solid aluminum electrolytic capacitors.

However, solid polymer niobium electrolytic capacitors do have a life time specification. The electrolyte deteriorates by a thermal degradation mechanism of the conductive polymer. The electrical conductivity decreases, as a function of time, in agreement with a granular structure, in which aging is due to the shrinking of the conductive polymer grains.^[17] The life time of polymer electrolytic capacitors is specified in similar terms like non-solid e-caps but its life time calculation follows other rules leading to much longer operational life times.^[18][19][20]

The different types of electrolytic capacitors show different behaviors in long-term stability, inherent failure modes and their self-healing mechanisms. Application rules for types with an inherent failure mode are specified to ensure capacitors high reliability and long life.

A rare failure in solid electrolytic capacitors is breakdown of the dielectric caused by faults or impurities. In niobium electrolytic capacitors the dielectric is niobium pentoxide (Nb₂O₅). Besides this pentoxide there is an additional niobium suboxide, niobium dioxide (NbO₂). The NbO₂ is a semi-conducting material with a higher conductivity than Nb₂O₅ but much lower than a short. In case of faults or impurities in the dielectric which evokes a partial dielectric breakdown the conducting channel would be effectively isolated by reduction of Nb₂O₅ into high ohmic NbO₂ if energy is limited.

As more energy is applied to a faulty solid niobium eventually either the high ohmic NbO₂ channel or the Nb₂O₅ dielectric breaks down and the capacitor exhibits a thermal runaway failure. In comparison to solid tantalum capacitors the thermal runaway of niobium anodes will occur at about three times higher power than of tantalum anodes. This gives a significant reduction (95%) of the ignition failure mode compared to solid tantalum capacitors.

The dielectric layer Nb₂O₅ of solid niobium electrolytic capacitors has a lower breakdown voltage proof than Ta₂O₅ in tantalum capacitors and therefore grows thicker per applied volt and so operates at lower field strength for a given voltage rating with the lower electrical stress the dielectric. In combination with niobium oxide anodes, which are more stable against oxygen diffusion that results in lower voltage derating rules compared with passivated niobium or tantalum anodes.^[8]

Electrolytic capacitor symbols

Electrolytic capacitor	Electrolytic capacitor	Electrolytic capacitor

Niobium capacitors are in general polarized components, with distinctly marked positive terminals. When subjected to reversed polarity (even briefly), the capacitor depolarizes and the dielectric oxide layer breaks down, which can cause it to fail even when later operated with correct polarity. If the failure is a short circuit (the most common occurrence), and current is not limited to a safe value, catastrophic thermal runaway may occur.

The standardization for all electrical, electronic components and related technologies follows the rules given by the International Electrotechnical Commission (IEC),^[25] a non-profit, non-governmental international standards organization.^[26][27] The definition of the characteristics and the procedure of the test methods for capacitors for use in electronic equipment are set out in the generic specification:

• IEC 60384-1, Fixed capacitors for use in electronic equipment – Part 1: Generic specification

Until now (2014) no IEC detail specification for niobium electrolytic capacitors is available.

For electronics manufacturers in the United States the EIA publish a standard for niobium and tantalum chip capacitors:

• EIA-717-A Surface Mount Niobium and Tantalum Capacitor Qualification Specification

• Niobium capacitors serve as a replacement for tantalum capacitors
• Niobium capacitors are available in SMD style, that makes them suitable for all portable electronic systems with flat design
• Niobium capacitors have no inrush current limitation
• Niobium capacitors are available with solid electrolyte for low ESR applications and stable electrical parameters
• Niobium capacitors have a limited number of manufacturers (AVX and Vishay)^[28]

• Types of capacitor

• R. P. Deshpande, Capacitors: Technology and Trends, ISBN 1-25900731-6 9781259007316 – Capacitors : Technology and Trends by R P Deshpande - AbeBooks
• D. Bach, Dissertation, 2009-06-05, Universität Karlsruhe (TH), EELS investigations of stoichiometric niobium oxides and niobium-based capacitors [8]
• Ch. Schnitter: The taming of niobium. In: Bayer research, Bayer AG, 2004 (2007-02-11), Wayback Machine
• Niobium Powder for Electrolytic Capacitor, JFE Technical Report No. 6 (October 2005) PDF
• Introduction to capacitors CapSite 2023