Pyranometer

A pyranometer (from Greek πῦρ (pyr) 'fire' and ἄνω (ano) 'above, sky') is a type of actinometer used for measuring solar irradiance on a planar surface and it is designed to measure the solar radiation flux density (W/m²) from the hemisphere above within a wavelength range 0.3 μm to 3 μm.

A typical pyranometer does not require any power to operate. However, recent technical development includes use of electronics in pyranometers, which do require (low) external power (see heat flux sensor).

The solar radiation spectrum that reaches Earth's surface extends its wavelength approximately from 300 nm to 2800 nm. Depending on the type of pyranometer used, irradiance measurements with different degrees of spectral sensitivity will be obtained.

To make a measurement of irradiance, it is required by definition that the response to "beam" radiation varies with the cosine of the angle of incidence. This ensures a full response when the solar radiation hits the sensor perpendicularly (normal to the surface, sun at zenith, 0° angle of incidence), zero response when the sun is at the horizon (90° angle of incidence, 90° zenith angle), and 0.5 at a 60° angle of incidence. It follows that a pyranometer should have a so-called "directional response" or "cosine response" that is as close as possible to the ideal cosine characteristic.

Following the definitions noted in the ISO 9060,^[1] three types of pyranometer can be recognized and grouped in two different technologies: thermopile technology and silicon semiconductor technology.

The light sensitivity, known as 'spectral response', depends on the type of pyranometer. The figure here above shows the spectral responses of the three types of pyranometer in relation to the solar radiation spectrum. The solar radiation spectrum represents the spectrum of sunlight that reaches the Earth's surface at sea level, at midday with A.M. (air mass) = 1.5.
The latitude and altitude influence this spectrum. The spectrum is influenced also by aerosol and pollution.

A thermopile pyranometer (also called thermo-electric pyranometer) is a sensor based on thermopiles designed to measure the broad band of the solar radiation flux density from a 180° field of view angle. A thermopile pyranometer thus usually measures from 300 to 2800 nm with a largely flat spectral sensitivity (see the spectral response graph) The first generation of thermopile pyranometers had the active part of the sensor equally divided in black and white sectors. Irradiation was calculated from the differential measure between the temperature of the black sectors, exposed to the sun, and the temperature of the white sectors, sectors not exposed to the sun or better said in the shades.

In all thermopile technology, irradiation is proportional to the difference between the temperature of the sun exposed area and the temperature of the shadow area.

In order to attain the proper directional and spectral characteristics, a thermopile pyranometer is constructed with the following main components:

• A thermopile sensor with a black coating. It absorbs all solar radiation, has a flat spectrum covering the 300 to 50,000 nanometer range, and has a near-perfect cosine response.
• A glass dome. It limits the spectral response from 300 to 2,800 nanometers (cutting off the part above 2,800 nm), while preserving the 180° field of view. It also shields the thermopile sensor from convection. Many, but not all, first-class and secondary standard pyranometers (see ISO 9060 classification of thermopile pyranometers) include a second glass dome as an additional "radiation shield", resulting in a better thermal equilibrium between the sensor and inner dome, compared to some single dome models by the same manufacturer. The effect of having a second dome, in these cases, is a strong reduction of instrument offsets. Class A, single dome models, with low zero-offset (+/- 1 W/m²) are available.

In the modern thermopile pyranometers the active (hot) junctions of the thermopile are located beneath the black coating surface and are heated by the radiation absorbed from the black coating.^[2] The passive (cold) junctions of the thermopile are fully protected from solar radiation and in thermal contact with the pyranometer housing, which serves as a heat-sink. This prevents any alteration from yellowing or decay when measuring the temperature in the shade, thus impairing the measure of the solar irradiance.

The thermopile generates a small voltage in proportion to the temperature difference between the black coating surface and the instrument housing. This is of the order of 10 μV (microvolts) per W/m2, so on a sunny day the output will be around 10 mV (millivolts). Each pyranometer has a unique sensitivity, unless otherwise equipped with electronics for signal calibration.

Photovoltaic pyranometer on a plane of arrays

Thermopile pyranometers are frequently used in meteorology, climatology, climate change research, building engineering physics, photovoltaic systems, and monitoring of photovoltaic power stations.

The solar energy industry, in a 2017 standard, IEC 61724-1:2017,^[3] has defined the type and number of pyranometers that should be used depending on the size and category of solar power plant. That norm advises to install thermopile pyranometers horizontally (GHI, Global Horizontal Irradiation), and to install photovoltaic pyranometers in the plane of PV modules (POA, Plane Of Array) to enhance accuracy in Performance Ratio calculation.

To use the data measured by a pyranometer (horizontal or in-plane), quality assessment (QA) of the raw measured data is necessary.^[4] This is because the pyranometer measurements typically suffer from environment-induced errors but also handling and neglect errors, such as:

• Pollution of the glass dome (e.g. deposition of atmospheric dust, bird droppings, snowfall), which reduces the measured irradiance
• Issues with positioning, resulting in measurements in a different plane (i.e. not horizontal or in-plane with PV modules) than expected
• Data logger errors resulting in e.g. static values, oscillations, or data capped to a certain value
• Reflections and shading from the surrounding objects resulting in inaccurate measurements (i.e. not corresponding to solar irradiance)
• Calibration issues of the instrument, leading to measurement errors, offset, or drift over time
• Dew, snow, or frost on the glass dome on lower-end pyranometers not equipped with heating units

Each of the above issues appears as a specific pattern in the measured time series. Thanks to this, the issues can be identified, the erroneous records flagged, and excluded from the dataset. The methods employed for data QA can be either manual, relying on an expert to identify the patterns, or automated, where an algorithm does the job. As many of the patterns are complex, not easily described, and require a particular context, manual QA is very common. A specialist software with suitable tools is required to perform the QA.

After the QA procedure, the remaining ‘clean’ dataset reflects the solar irradiance at the measurement site to within the uncertainty of measurement of the instrument. The ‘clean’ measured dataset can be optionally enhanced with data from a satellite-based solar irradiance model. This data is available globally for a much longer time period (typically decades into the past) than the data measured by the pyranometer. The satellite model data can be correlated (or site adapted) to the pyranometer-measured data to produce a dataset with a long time period of data accurate for the specific site, with a defined uncertainty. Such data can be used to perform bankable solar resource studies or produce Solar potential maps.

For monitoring of operational PV power plants, pyranometers play an essential role in verifying the solar irradiance available at any given time or over a certain time period. Due to weather variability, redundancy, and the spatial scale of contemporary solar plants (above 100MWp), multiple pyranometers are installed to provide accurate solar irradiation for each section of the PV power plant. IEC 61724-1:2017^[5] international standard for example calls for at least 4 Class A thermopile pyranometers to be installed at 100MWp PV power plant at all times.

Solar measurements that were QA’d could be used to derive Key Performance Indicators (KPI) such as Performance ratio* - metrics used in asset health monitoring or various contractual scenarios relating to energy produced (billing) or asset management (i.e. O&M). In these calculations, the measured sum of in-plane irradiation over a certain period is used as the determinant to which normalized produced PV electricity is compared to. Due to the difficulty of obtaining reliable in-plane measurements, especially in operational power plants, Energy Performance Index is increasingly being used instead of the older Performance ratio metric.

Also known as a photoelectric pyranometer in the ISO 9060,^[6] a photodiode-based pyranometer can detect the portion of the solar spectrum between 400 nm and 1100 nm. The photodiode converts the aforementioned solar spectrum frequencies into current at high speed, thanks to the photoelectric effect. The conversion is influenced by the temperature with a raise in current produced by the raise in temperature (about 0,1% • °C)

A photodiode-based pyranometer is composed by a housing dome, a photodiode, and a diffuser or optical filters. The photodiode has a small surface area and acts as a sensor. The current generated by the photodiode is proportional to irradiance; an output circuit, such as a transimpedance amplifier, generates a voltage directly proportional to the photocurrent. The output is usually on the order of millivolts, the same order of magnitude as thermopile-type pyranometers.

Photodiode-based pyranometers are implemented where the quantity of irradiation of the visible solar spectrum, or of certain portions such as UV, IR or PAR (photosynthetically active radiation), needs to be calculated. This is done by using diodes with specific spectral responses. Photodiode-based pyranometers are the core of luxmeters used in photography, cinema and lighting technique. Sometimes they are also installed close to modules of photovoltaic systems.

Built around the 2000s concurrently with the spread of photovoltaic systems, the photovoltaic pyranometer is an evolution of the photodiode pyranometer. It answered the need for a single reference photovoltaic cell when measuring the power of cell and photovoltaic modules.^[7] Specifically, each cell and module is tested through flash tests by their respective manufacturers, and thermopile pyranometers do not possess the adequate speed of response nor the same spectral response of a cell. This would create obvious mismatch when measuring power, which would need to be quantified.^[8][9] In the technical documents, this pyranometer is also known as "reference cell".

The active part of the sensor is composed of a photovoltaic cell working in near short-circuit condition. As such, the generated current is directly proportionate to the solar radiation hitting the cell in a range between 350 nm and 1150 nm. When invested by a luminous radiation in the mentioned range, it produces current as a consequence of the photovoltaic effect. Its sensitivity is not flat, but it is same as that of Silicon photovoltaic cell. See the Spectral Response graph.

A photovoltaic pyranometer is essentially assembled with the following parts:

• A metallic container with a fixing staff
• A small photovoltaic cell
• Signal conditioning electronics

Silicon sensors such as the photodiode and the photovoltaic cell vary the output in function of temperature. In the more recent models, the electronics compensate the signal with the temperature, therefore removing the influence of temperature out of the values of solar irradiance. Inside several models, the case houses a board for the amplification and conditioning of the signal.

Photovoltaic pyranometers are used in solar simulators and alongside photovoltaic systems for the calculation of photovoltaic module effective power and system performance. Because the spectral response of a photovoltaic pyranometer is similar to that of a photovoltaic module, it may also be used for preliminary diagnosis of malfunction in photovoltaic systems.

Reference PV Cell or Solar Irradiance Sensor may have external inputs ensuring the connection of Module Temperature Sensor, Ambient Temperature Sensor and Wind speed sensor with only one Modbus RTU output connected directly to the Datalogger. These data are suitable for monitoring the Solar PV Plants.

Both thermopile-type and photovoltaic pyranometers are manufactured according to standards.

Thermopile pyranometers follow the ISO 9060 standard, which is also adopted by the World Meteorological Organization (WMO). This standard discriminates three classes.

The latest version of ISO 9060, from 2018 uses the following classification: Class A for best performing, followed by Class B and Class C, while the older ISO 9060 standard from 1990 used ambiguous terms as "secondary standard", "first class" and "second class".,^[10]

Differences in classes are due to a certain number of properties in the sensors: response time, thermal offsets, temperature dependence, directional error, non-stability, non-linearity, spectral selectivity and tilt response. These are all defined in ISO 9060. For a sensor to be classified in a certain category, it needs to fulfill all the minimum requirements for these properties.

‘Fast response’ and ‘spectrally flat’ are two sub-classifications, included in ISO 9060:2018. They help to further distinguish and categorise sensors. To gain the ‘fast response’ classification, the response time for 95% of readings must be less than 0.5 seconds; while ‘spectrally flat’ can apply to sensors with a spectral selectivity of less than 3% in the 0,35 to 1,5 μm spectral range. While most Class A pyranometers are ‘spectrally flat’, sensors in the ‘fast response’ sub-classification are much rarer. Most Class A pyranometers have a response time of 5 seconds or more.

The calibration is typically done having the World Radiometric Reference^[11] (WRR) as an absolute reference. It is maintained by PMOD^[12] in Davos, Switzerland.^[13] In addition to the World Radiometric Reference, there are private laboratories such as ISO-Cal North America^[14] who have acquired accreditation for these unique calibrations. For the Class A pyranometer, calibration is done following ASTM G167,^[15] ISO 9847^[16] or ISO 9846.^[17][18] Class B and class C pyranometers are usually calibrated according to ASTM E824^[19] and ISO 9847.^[20]

Photovoltaic pyranometers are standardized and calibrated under IEC 60904-4 for primary reference samples and under IEC 60904-2 for secondary reference samples and the instruments intended for sale.

In both standards, their respective traceability chain starts with the primary standard known as the group of cavity radiometer by the World Radiometric Reference (WRR).^[21]

The natural output value of these pyranometers does not usually exceed tens of millivolt (mV). It is considered a "weak" signal, and as such, rather vulnerable to electromagnetic interferences, especially where the cable runs across decametrical distances or lies in photovoltaic systems. Thus, these sensors are frequently equipped with signal conditioning electronics, giving an output of 4-20 mA or 0-1 V.

Another solution implies greater immunities to noises, like Modbus over RS-485, suitable for ambiances with electromagnetic interferences typical of medium-large scale photovoltaic power stations, or SDI-12 output, where sensors are part of a low power weather station. The equipped electronics often concur to easy integration in the system's SCADA.

Additional information can also be stored in the electronics of the sensor, like calibration history, serial number.

• Actinometer
• Photodiode
• Heat flux sensor
• Net radiometer
• Pyrgeometer
• Pyrheliometer
• Radiometer
• Sunlight
• Solar constant
• Sun path

Wikimedia Commons has media related to Pyranometer.

• Meteo-Technology instrumentation website
• Website showing measured data using a thermopile pyranometer north to the arctic circle