National Rail NR class

UGL Rail Cv40-9i
NR2 in Pacific National livery on an intermodal train
Type and origin Power type Diesel-electric Builder A Goninan & Co Broadmeadow (NR1–NR60) Bassendean (NR61–NR120) Model General Electric Cv40-9i Build date 1996–1998 Total produced 120
Specifications Configuration: ​  • UIC Co-Co Gauge 1,435 mm (4 ft 8+1⁄2 in) standard gauge Bogies Co-Co Length 22 m (72 ft 2 in) Width 2.94 m (9 ft 8 in) Height 4.25 m (13 ft 11 in) Loco weight 132 tonnes Fuel type Diesel Prime mover GE 7FDL-16 Engine type V16 engine Generator GE GMG196 Traction motors GE 5GE793A1 Head end power No Cylinders 16
Performance figures Maximum speed 115 km/h (71 mph) Power output 3,000 kW (4,000 hp) Tractive effort 520 kN (116,900.65 lbf)
Career Operators National Rail Pacific National Number in class 120 Numbers NR1, NR2, NR4–NR32, NR34–NR40, NR42–NR78, NR81–NR122 First run 18 September 1996 Current owner Pacific National Disposition 117 in service, 3 scrapped

The NR class are Australian diesel-electric locomotives built by A Goninan & Co for National Rail between 1996 and 1998. They are currently operated by Pacific National. The C44aci model locomotives built by UGL Rail at Broadmeadow adopted the design from the NR Class.

When National Rail commenced operations in April 1993, it inherited a diverse collection of rolling stock and locomotives from various operators to operate interstate freight services in Australia.^[1] The fleet included locomotives of mixed age and power, leased from FreightCorp, V/Line and Australian National.

In September 1995, National Rail awarded a contract to A Goninan & Co for 80 locomotives, which later became 120. NR1–NR60 were built at Broadmeadow, and NR61–NR120 were constructed at Bassendean.^[2][3] The frames were built at Hexham and the bogies at Goninan's Landsdowne Engineering subsidiary in Taree.^[2][3]

The first locomotive to be completed was NR61, which was trialled on 18 September 1996, between Midland and Jumperkine.^[4] The first Broadmeadow-built unit ran on 23 September 1996.^[4] The early units were delivered without National Rail branding or logos, but later locomotives were delivered in the full livery. Testing was carried out on the NSW Main Northern line between Werris Creek and Maitland, using ballast wagons and 442 class locomotives, in dynamic braking mode, as dynamic loads.^[5] Each locomotive was required to accumulate 10,000 kilometres (6,200 mi) of trouble-free running before being accepted.^[2] The final unit was delivered from Broadmeadow in February 1998.

As part of its contract, A Goninan & Co was required to maintain the fleet. A depot was built alongside the Newport to Sunshine railway in the western Melbourne suburb of Spotswood to cater for this.^[2][3]Pacific National announced in September 2022 that the company had committed more than A$160 million towards the overhauling of the company's NR class units for East – West Intermodal traffic.^[6]

With the arrival of the class, National Rail was able to return leased units to their respective owners, including 422, 80, 81, and 82 class locomotives to FreightCorp, and 442s and 48s class locomotives to Silverton Rail.

The V/Line C class (which were owned by National Rail) and relatively new EL class were withdrawn and stored.^[2][7] Once all 120 units were delivered, National Rail retained the AN, BL and DL class locomotives, along with thirteen 81 class and several hired G class. The new locomotives were placed on time sensitive trains first.^[2]

When first delivered, the NR class were banned from running in New South Wales by the Environment Protection Authority due to excessive noise when under dynamic braking but the ban was lifted after further testing. The class could also not lead on the Victorian standard gauge network due to the lack of suitable radio equipment. In later years NR76 to NR98 were provided with V/Line Section Authority System equipment to work the Western standard gauge line, while NR1 to NR13 and NR61 to NR72 were fitted with V/Line radios to operate on the Victorian North East line.^[2]

Great Southern Rail contracted National Rail to provide locomotives and crews for their Passenger services, the first train running with NR77 on 1 November 1997. All locomotives were included in the sale of National Rail to Pacific National in February 2002.

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed. (September 2023) (Learn how and when to remove this message)

On 19 May 1998, NR3 was involved in an accident with a collapsed bridge at Robertson while hauling a Steel train that resulted in fatalities to the two train drivers; it was later rebuilt and renumbered as NR121 out of respect.^{[citation needed]}

In late May 2006, NR33 was involved in a level crossing incident at Lismore, being the third locomotive on Adelaide to Melbourne freight service AM3, behind DL40 and NR52. A truck drove into the side of the NR during low visibility conditions and the subsequent accident saw approximately 1200 metres of the train land on top of NR33, the NR was subsequently written off and scrapped in Bendigo after an inspection to see how viable a return to service would be.^{[citation needed]}

On 30 January 2009, train 5PS6 derailed at a washaway near Golden Ridge, just east of Kalgoorlie in Western Australia. Locomotives NR35 and NR51 finished up on their sides, badly damaged, and spent several years out of service before the decision was made to repair them.^{[citation needed]}

On 3 April 2016, NR8 was involved in a engine fire at Cardiff, NSW. The locomotive was rebuilt during 2016. NR's 48 and 81 had suffered similar fires several years earlier, both also were repaired but without the Pacific National signage on their hood sides.^{[citation needed]}

On 21 April 2016, train 3MP5 derailed near Rawlinna in Western Australia. The two locomotives, NR34 and NR50, were badly damaged, but both were rebuilt and returned to service in late 2016 and mid 2017 respectively.^[8]

On 24 December 2019, 7MP5 hauled by NR80/NR59 collided with the rear of 2K66 Watco/CBH grain train, at Jumperkine, Western Australia, which resulted in a driver fatality. NR59 was later forwarded back to Melbourne, while NR80 was rebuilt at UGL Bassendean, being released as NR122 during early 2021.^[9]

On 25 February 2021, 4BM4 hauled by NR43/AN3/NR39 derailed at Nana Glen due to track washaway from extensive flooding. NR43/AN3 stayed on the tracks while NR39 ended up on its side, with half the train derailing behind it. NR39 was repaired and repainted later in the year.^{[citation needed]}

On 31 December 2023, emergency services were called to the Barrier Highway after train 7SP5 with NR41/NR79 collided with a truck. The crash caused the deaths of both train drivers. The truck driver was uninjured. Both locomotives Cab Destroyed were scrapped during the clean up of the site.^[10]

The NR Class introduced many new features. These were the first locomotives in Australia to have "variable horsepower", which meant that the power output of the engine had three different settings, making the NR class the most fuel-efficient locomotives in Australia.^{[citation needed]} They have GE 7FDL-16 engines, with power levels of 2,850 hp (2,130 kW), 3,560 hp (2,650 kW) or 4,020 hp (3,000 kW), mass of 132 t (130 long tons; 146 short tons), a Co-Co wheel arrangement and a maximum speed of 115 km/h (71 mph).^{[citation needed]}

The NR Class cab was designed taking into consideration the results of an extended consultative process with the end users. This has resulted in a cab that has been well accepted. The layout of the control stand evolved from a British Rail Class 60 cab, and is substantially different from the more common AAR type I (stand) and Type II (desk) cabs.^[11]

The design is a long hood unit locomotive, with only one cab but two separate sets of controls, which allow it be driven either "A" or "B" end leading. This locomotive had to pass all tests, such as being able to shunt if required, drive "long end leading" if needed, and allow drivers to do checks on fuel, brakes, and sand. Despite the twin controls, operation of the class "B" end leading is avoided, with single NR classes being turned on turntables or rail triangles to ensure they face the correct way.^[2]

In 2013, UGL Rail, Spotswood fitted NR17 with ECP/WDP braking systems for use on quarry traffic in New South Wales. It was reclassified as NRE17 during December of that year, but that code was reverted very quickly and more recent photos indicate the normal code. The cabside decals of NR120 were also altered to permit addition of the "E", but there is no evidence that this ever happened.^{[citation needed]}

• NR class database at Railpage
• Media related to NR class at Wikimedia Commons